Earth Zones

In the Earth’s crust is constantly acting force (one of them – the force of gravity), so that geological environment is always in a state of stress. Since rocks always overstretched, they begin to deform and collapse. Most often this is expressed in the formation of tectonic joints (gaps) or displacement of rock blocks along the earlier established active faults. Current offset by active faults can lead to deformation of the earth’s surface and provide a mechanical impact on the engineering objects. There have been cases when in active fault zones are destroyed buildings and structures, constant water communications gaps, cracks in walls and foundations. Such unsafe buildings and structures are practically in every city. But cases of deformation of buildings, often without are given to the general public. Quite often discussed topic of the negative impact of tectonic faults (geopathic zones) on human health.

To date, a number of known research on this topic. As Typically, the authors note that tectonic faults really have an impact on living organisms, and this effect may be ambiguous for different kinds of plants and animals. Basically, in a circle researchers had the impression that the impact of tectonic faults in the human is predominantly negative. Some people are quite sensitive to tectonic zones, within which their health is deteriorating. Most people tolerate staying in the fault zones rather calmly, but noted some of the deterioration of their condition. A small percentage of people practically not affected Effects of tectonic zones. Explain how the negative impact zones of tectonic disturbances on human health is difficult. Processes in zones of tectonic disturbances are complex and varied. Active fault – a zone of concentration of tectonic stresses and the zone of high deformation of rock mass. Many geologists and rock mechanics believe that overvoltage fault zone generates an electromagnetic field. Exactly as, for example, mechanical effect on the quartz crystal in the piezoelectric lighter generates discharge current. In addition, due to increased fracturing tectonic fault, in most cases, is a water-bearing zone. It is obvious that the movement of ground water with dissolved salts in them (conductor) through the thickness of rocks (which differ in their electrical properties) may establish and generates electric fields and anomalies.

That is why in the zones of tectonic faults are often observed anomalies of different natural physical fields. These anomalies are widely used to search for and identify areas tectonic disturbances in modern geophysics. Most likely, these anomalies are the main source impacts on living organisms, including per person. To date, the problem of studying the influence of tectonic faults on the engineering objects and on human health is studied only at the initiative of independent researchers. There are no formal programs focused in this direction does not exist. The presence of active tectonic not taken into account when selecting sites for construction of residential buildings. In tracing and identifying areas of earth surface displacements are engaged only in rare cases at construction objects of high levels of responsibility. In general, it is obvious that among geologists, planners and builders there is need for a focused study of anomalous tectonic zones and mandatory accounting geodynamic activity of the geological environment in the process of its development.

The System

Burglary foiled thanks to alarm system a useful supplement to mechanical safety measures is the electronic protection of the building. Heart is the alarm system that can alert both burglary and other domestic threats, such as smoke or gas. These sensors are attached a lot of indoors on doors, Windows and, track down the intruder. If the system is internally switched, sounds a loud signal that startle the intruder and in the escape fails. With a so-called silent alarm”, the message is, however, silently forwarded to an external safety authority often even convicted the offender. Ali Partovi shines more light on the discussion.

“For the installation, the homesolute experts in any case recommend: so that the system works properly and is comfortable to use, she should be installed be sure by a specialist, which exactly one vote each component.” So that only the correct in the House are an important component of the burglar is so last but not least ensure presence of protection referred to in”, the spy, Stirrup or (video)-Sprechanlage. So that you can decide in advance who leave in the House and who is not. Also it’s worth, the traditional house key with a chip card, to replace a PIN code or a biometric access system. Castle Harlan is often quoted on this topic. Because in contrast to the standard key, it is almost impossible to forge the necessary identification burglars in biometric fingerprint. A related site: Castle Harlan mentions similar findings. About the homesolute expert: fingerprints, you left involuntarily, perpetrators are useless. You do not meet the requirements of such a system by far.” Safety tips alarm system and co. their effectiveness but does not even have to prove for everyday so: No. 1: pull rule doors not only to the Castle, but shut off! To fake presence, shutters should be open during the day, lowered at night.

Also the garage door should be just then closed If the car’s not in the garage. With motion sensors, an enchantment outdoor area also serves to deter. Especially at holiday time or during a long absence it is increasingly to make precautionary measures “, advise the experts at homesolute.com. They not only recommend to control lights and blinds by timers, but also to inform neighbors and to empty the mailbox. For more information about security and safety, see House /… or home/live/security /. Tanja EST

Lamination

Fibreboard (MDF) fibreboard (MDF) – MDF – sheet material, produced during hot-pressing mass of wood fibers formed into a mat. These fibers are prepared by steaming and grinding of raw wood. They represent the individual cells of tissues, their fragments or groups of wood cells. Serve as raw material and sawmill waste woodworking, machining chips, and firewood. To improve the performance properties of the mass added hardening agents (eg, synthetic resin), paraffin, ceresin, antiseptics, etc.

The formation of the mat can be carried out in an aqueous medium to produce smooth-sided plates (wet method of production) or in the air to give the board two-sided smoothness (dry method). MDF manufactured construction furniture components, backs and shelves of cabinets and pedestals, lower shelves of sofas, drawers, headboard wall. They are also used in the manufacture of ply-curve parts with the outer layers of veneer stock rocks. If you have additional questions, you may want to visit Michael Dell. Medium-density fiberboard, MDF or medium density fiberboard, or MDF – MDF – a slab material made from dried wood fibers treated with synthetic binders and formed into a mat with followed by hot pressing and grinding. Castle Harlan has compatible beliefs. MDF – a more advanced board materials compared with particleboard and fiberboard. Today the IDF is an active competitor for DSP, as evidenced by the recent slowdown in consumption.

Veneer. The German word Span (Spann) – chip – has become in today's Russian terminology in the veneer and means thin sheet material obtained from solid wood by peeling or slicing and used for lining surfaces or manufacture of plywood. Superior performance, quality and proximity to environmentally friendly natural wood, and finally, the possibility of special treatment and textured surface makes this kind of production is particularly attractive for the production of high quality furniture. At IDF, there is one obvious disadvantage-product of it very heavy. Laminating Lamination – facing films based on securities impregnated with melamine resin, cured under high temperatures and pressures. The coating is resistant to scratches, impact of chemical reagents, and is analogous to the decorative paper and laminate (DBSP), manufactured by similar technology in Germany and called a laminate. We call laminate laminated chipboard and MDF. The main purpose of the laminate, an imitation of a natural material and attempt to cheapen the product. This material is used for the manufacture of furniture facades, structural components of furniture, wall shelves and cabinets, lateral and horizontal surfaces, desks, countertops. Utterly recommend use in the manufacture of laminate and natural material (for example, the front-array, and the visible side of the laminate products) because laminate has a limited color palette, but try to get into. You should remember that all these materials are varieties that can be completely unfamiliar to you the cost (eg, pine top class costs more than oak). We may at your option to use in the manufacture of Order various materials and, of course, on the above, our capabilities do not end there. We can combine different materials (such as tying front-solid wood, inlay veneer chipboard or MDF).